*EXAMPLE* TD-0000 Requesting Deployment

[FIVE]

Please follow this thread as an example format If you are ready to request deployment as a MEPD S.W.A.T. Officer.

Notes and instructions are posted in bold red type.

The "Topic Title" should be: TD-XXXX Requesting Deployment

The "Topic Description" should be the name of the trooper you are emulating. A list of those troopers and their configurations can be found on the S.W.A.T. requirements list here: http://www.mepd.net/crl/#SWAT

BEFORE posting your thread make sure you have reviewed the MEPD S.W.A.T. requirements here: http://www.mepd.net/crl/#SWAT If you have questions about your armor please post in The Hurt Locker before creating a deployment thread.

---------------------------------------------------------

1) Post your personal information in bold:

Name: John Doe Example

Legion ID #: TD-0000

Forum Name: ExampleSandy

Garrison: Example

Trooper Emulated: Captain Example Version

2) Post at least two, nice sized, clear photos of you in your armor at various angles. These photos will be used, in part, to determine if your weathering is satisfactory.

Copy and paste the first three requirements from the S.W.A.T. requirements into the post in bold and note that you have achieved this to the best of your knowledge.

Member must currently be deployed as an MEPD Police Officer to be considered. - yes

Weathering must be appropriate to screen used armor. Too little or too much weathering will not be allowed. - yes

Pack, pauldron, and weapon combinations must match a specific trooper a seen on screen. - yes

3) Post a close up photo of each major area and/or item listed in the S.W.A.T. requirements while continuing to copy and paste the requirements they relate to above the photo in bold.

Pauldrons must be of the accurate “puffy” variety. Older style/flat and brightly/off color pauldrons are not allowed.

Packs must have the appropriate details for the specific trooper which is being referenced.

Pouches must be of the correct construction, color, and materials as reference trooper.

4) You may post multiple requirements met with the same photo... like so...

Rubber gloves.

Latex or silicone (i.e., “soft”) hand plates.

Rivets on the left side of the ab/kidney plates: a total of six rivets with three on the ab and three on the kidney plate, equally spaced out along the depth of the armor and about 10mm from the edge.

One snap on the top right hand side oft he ab plate: back of male side of snap should show on outside of ab plate.

Visible fasteners under crotch area. Two (or 3) male snaps in the back and one split rivet or brad in the front. (not required to be functional)

Boots must be screen accurate in color and make; they cannot have a seam on the front.

FXhelmets, MRCE and/or ANHv2 helmets are not allowed.

Hasbro blasters are not allowed, even conversions.

5) Post at least one "action" image. This photo should be taken of you from the waist up on a blank, non-colored wall (i.e., such as white, beige, grey, etc.) This photo should be taken and available in high-resolution for the deployment photo.

NOTE: There is no need to repost photos of details which were needed for Police Officer deployment. Please — simply ease of reading posts — make sure there is a "space" between each bolded statement and each image.

The following post/reply is as your actual deployment request should look without the instructions. [/i]

[FIVE]

Name: John Doe Example

Legion ID #: TD-0000

Forum Name: ExampleSandy

Garrison: Example

Trooper Emulated: Captain Example Version

Member must currently be deployed as an MEPD Police Officer to be considered. - yes

Weathering must be appropriate to screen used armor. Too little or too much weathering will not be allowed. - yes

Pack, pauldron, and weapon combinations must match a specific trooper a seen on screen. - yes

Pauldrons must be of the accurate “puffy” variety. Older style/flat and brightly/off color pauldrons are not allowed.

Packs must have the appropriate details for the specific trooper which is being referenced.

Pouches must be of the correct construction, color, and materials as reference trooper.

Rubber gloves.

Latex or silicone (i.e., “soft”) hand plates.

Rivets on the left side of the ab/kidney plates: a total of six rivets with three on the ab and three on the kidney plate, equally spaced out along the depth of the armor and about 10mm from the edge.

One snap on the top right hand side oft he ab plate: back of male side of snap should show on outside of ab plate.

Visible fasteners under crotch area. Two (or 3) male snaps in the back and one split rivet or brad in the front. (not required to be functional)

Boots must be screen accurate in color and make; they cannot have a seam on the front.

FXhelmets, MRCE and/or ANHv2 helmets are not allowed.

Hasbro blasters are not allowed, even conversions.