TK1336

Hummmmmmmmmmmmmmm! I know someone who needs a Set of 2 hip Pouches, Also Your Welcome

Hi, Very Good Job, You know I put these templates out on my website for members to be able to make thier own, but don't want my pictures used to post on others site so Please Don't do it. If you want to see how to make your own go here:http://www.tk1336.com/mp40ammopouch.html These are for everyone to make if they want.

Well the only one I have for sale is the one proto-type One of the 1st ones I did. I do need to make another one to match the one I just finished.

Yes re-did the Template and made a new one from it and yes looks a lot better. This one is it.

Thanks, Anyone who wants to make some ammo pouches can. I just ask don't copy them and post them on other websites. I still need to scan them and people can download and print them out. It has been a year sence I worked with leather the last thing I made was a jawa Ion Blaster holster. Please note when you make the flaps, I did up date the width. I may re-due these two pouches to that new size. You can see on my 1st Post I did adjust the flap width and the belt loop width and I think it does look better.

Sure that is what it is there for "Troopers Helping Troopers" I am adjusting the flap size (Width) and overall lenth from new info I got and they will turn out better than the ones shown. One thing the Flaps are not wide enough on the ones I made. So I am making 2 more now with that adjusted into them. I will post that on my site too. I should have one done this weekend these really don't take to long to make only have to wait on the material to make them. And I may sell the 1st ones I did I think at some point in time.Once I get them down right.

Thanks, that would help a lot, Yep I work about 50 hrs a weak so not much time left to research. Still have to finish my TD armor, my helmet is done but will need to dirty it up along with these pouches. May make more accurate ones if I get the right info. If you want to see the back side of the pouches just go here http://www.tk1336.com/mp40ammopouch.html And if I get some canvas I could make a Canvas shoulder pouch with a small tool pouch attached.

oh, no problem I could not add to that reply to say this was the only info I found on the subject so that is what I used. Is it true or not? All I can see is the pictures and do a close job to it. So no I am not offended in any way. I need the feedback I want to know how accurate these are. One thing that does make sence is that they did redue some pouches to suite thier needs. I am sure I would have purchased lots of ammo pouches of the same type and got them cheep if they were damages and just repaired them the best I could to make a good looking movie prop. That is what I think they did. Also at that time yes you could buy ammo pouches cheep, not like today.

The shoulder pouch seen on the "Move Along" trooper and "Look Sir, Droids!" trooper has the same basic shape of the standard pouch. However it has a much more complex strapping system which inlcudes shorter flaps, long, thin, leather straps and leather strap retaining loops. This pouch also has a "4th" pouch; a small tool pouch located near the bottom of the last elongated pocket. Both canvas and leather versions of this pouch are available. Most of the canvas versions available are replicas as authentic canvas pouches of this kind are not easily found and quite expensive. The leather versions are more rare yet. After a year of searching I have only seen 2 complete leather sets and two incomplete leather sets. All were authentic, German MP-40 pouches. Go to http://www.looksirdroids.com/replica_pouches_leather-canvas.htm Thanks

Yes I started a post and a how to on my website page http://www.tk1336.com/mp40ammopouch.html

Thanks Guys was not sure I got them right, I had seen some pictures from the movie with the flaps attached in the back with rivets and and some that are not cut off and re-attached in the back but they are one whole part. So I did one of each. The hard one was the shoulder pouch. This is the shoulder pouch with the tool pouch.The tool pouch clips on to the 3rd pocket. With some reference pictures is what I went by. When it is attached and you lean over it looks just like the snap shot taken from ANH.

Thanks Bluey, Working on my TD armor again too.. I just hope I have the right measurements on all the pouches. That would suck if I had to redue all of them over again. :o

Well I had a task of making my own MP-40 3 pocket hip pouches just not sure if they are correct. I only have info from some guys and pictures and another website. I even made a "How To" on my website just not sure about the correct measurements. Some feedback would help. I also made the MP-40 Shoulder Pouch with the small tool pouch. All made of leather and all made by hand by me. You can see the how to on my website here: http://www.tk1336.com/mp40ammopouch.html I know most of you have these or have seen them close up. I am guessing here the size of the pouches are 10" high and 5-1/2" wide the pockets are 1-1/4" deep. I am adjusting the new ones I am making to match the same size as the shoulder pouch to me it looks more accurate in size and shape. You Tell Me? Thanks I adjusted one of the pouches, the flap width and belt loop this is the front and back. Yes these will be FOR SALE I will post them on the For Sale/ For Trade section once I upgrade the other one to match this one. info is also on my website.

B)YesPOS - CLOSED

I Second That I have one too And it just blew me away!!!! That's why I highly recommend him you just can't go wrong.

Cool but where did you get all the parts to makre it ? So far I have a Frame and soon the cistern and trays, I have the PVC tube and the caps, and TD plate thats it don't know the rest or the size needed yet, Hey but I am still Looking. Good Luck With Yours.

Any one make a list of parts need to build this and maybe website/ store to get said parts that would help Great I am starting mine real soon. Not Sure on where to start.