Jump to content

Wook's Docking Bay 94 Captain Build (AP)


Wook1138
 Share

Recommended Posts

A few more things done on the build.  Pretty much all the gluing is done with a few small exceptions.  All holes are drilled and I think I'm ready for some strapping. Anyway, here is what I've been up to.


Sizing the shins and thighs.  Here is my crazy method of figuring out how much to trim off each side so that it fits and the seam will run at a nice angle down my leg.  I hope it works.
6e3eb8ab30362c49bd2a7792ca9c506f.jpg

 

Belt and thigh ammo belt trimmed and ready for installation. 
303e5925f9e9b83ea736eee23b516c85.jpg

 

Kept my trim to about 4mm - default for how Mark pulls these pieces.
851920f48cd14e1ed8983f9739501c13.jpg

 

My 45° cut on the belt is 10mm to fit my canvas belt properly.  The canvas belt is sitting a bit low in the picture, but it does meet up with where the 45° cut meets the outside edge.
063788290bc51a8c2bd544fbfbd16f4c.jpg

 

I had to do a whole whack of hot bathing and heat gun.  I needed to reshape my kidney piece and make it not so wide.  I traced the original shape on to cardboard for reference and used hot baths to squish the outsides in a little.  This caused buckling of the top and bottom return edge, so I had to use a heat gun and some pieces of wood to reshape the return edge.  Sorry no after pics, but it worked out pretty good - mind you, I am terrible at hot baths and heat guns. 
ac9352a3c147ed44d79db7c7948aaf3e.jpg

 

Also had to reshape how the back meets the kidney.  This is an issue with my TK as well - no amount of strapping adjustments could fix it. the back seems to pivot at the outer edges when fitted to my body.
e72592de47cc3e113232560452d29b53.jpg

 

This is the return edge along the top of the kidney and AB.  The AB side flares up so I also had to reshape that too.  Again, no "after" pics.  But all is good now. Also shaped my shins to they close better and my posterior to avoid "butt flare".
53e1890575a1ed3251536741e956eb08.jpg

 

Marked the hole for the cod.  Measured about 1-1/8 inch from end and drilled with 1/8" bit for a split rivet.
386cd37923145bfcd462d436764e68c3.jpg

 

Posterior.  Two 5/32" drill holes for line 24 snap bases.  I think I measured about 1" from edge and then another 7/8" for second hole.
0d0da4d829dc221984b6bbd4cd43a166.jpg

 

5/32" hole for snap in right Ab connection.  The hole ended up being about 18mm from edge and top.
186f347db3b816f5bcd988d114c8edd2.jpg

 

1/8" holes for split rivets along left ab to kidney connection.  the holes are 10mm from seam.  20mm upper return edge and there is about 58mm between each hole. 
0c1f6d274094c5071e694020793020ad.jpg

 

So, at this point, all the arms and legs are assembled except for the 25mm back coverstrips for the shins.  I still need to drill holes on the Ab for the belt and assemble belt.  And some trimming of coverstrips here and there.  Also need to finish up the helmet.  And then... I can finally start getting dirty.:td:
e84deb3e0c123411ed6c5feb4632d5fb.jpg

 

Need to trim for the three-button button plate and the sniper knee.
f252d0bfaa022db350503db1d291a97e.jpg

 

 

 

Anybody know how thick this thing should be?  Time to do some research... .
2a1f9d0e9beee3a6ebe4a26921cfe17a.jpg


 

Link to comment
Share on other sites

Sniper knee plate. A lot easier than a TK knee (for the AP kit at least). Added some pieces of plastic to the back and glued into place. I hope it is enough to hold. The shin is curved and the plate is flat, so I piled on the E6000 and will hope for the best.

5bdc7a1d4cbe35e226ad9c1334ef5843.jpg

f04ebdd5ab2e4410e4f8ecf8bf939d3c.jpg

f78f265dd68a0cd07cec7baff4df7a7c.jpg

Reference - in addition to RoCko's pics.


ad64c67ee484d8df3e70bc8d5a42945d.jpg

ae9853edccb615f90a741c56b07b2621.jpg

Also trimmed this guy.
f0e8a8cc9270ae54d6b02760da78716d.jpg
Reference pic
fba2ebcc2c12163640403ddf23252ca9.jpg

 

Link to comment
Share on other sites

Looking at it from the side, it seems to sit a little low, especially compared to the reference pics of the dockingbay captain. 

Oh yeah. Thanks! Let’s try this again.
e546949ff5ffe8cd8c63e13418415735.jpg

031ba070cdaa9fc84be06373a2631f8f.jpg


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

Sniper knee is looking good now:yes:

Concerning your question about the ammobelt, attach it in the regular position for basic approval and PO and then move it slightly down for SWAT. 

I suppose the chest from the picture above isn't the one you will be using for this present build? 

Link to comment
Share on other sites

Sniper knee is looking good nowdark_yes.gif
Concerning your question about the ammobelt, attach it in the regular position for basic approval and PO and then move it slightly down for SWAT. 
I suppose the chest from the picture above isn't the one you will be using for this present build? 

Thanks!

Chest is for the TK.


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

On to snaps and belt.

First off - Belt: I used the standard measurements (various builds and the Billhags diagrams) for placing the snaps on the ab on my first build - the left side of the ab calls for 59mm from the return edge as shown below.  this is way too much for this armor.  I went with 40mm instead and it worked perfect.  The right side stays the same - 28mm.

81b02ff9e5c149289dc07a08666f6b30.jpg

 

Usual measurements

33389284862_9e0a8214f5_o.jpg

 

By the way, taping the anvil to the back side of the armor works great for setting these snaps.
a531426fcc9fde63f64ed62427abf666.jpg

 

Also reaming out the holes helps the snaps (male base) to sit flush.
81f3ce94e9928f8421884b3f7a4902e0.jpg

 

The left belt snap (tandy line 24) and two snaps for the posterior.
9befc8a68b9455b9446216bed6bc1f0e.jpg

 

Right ab to kidney connection snap and the right belt snap.
6b62c0fde2b92a243090a65e56c341c8.jpg

 

Once I've centered by belt to the armor, I taped it in place.  I took a sharpie marker and marked up the snaps on the armor - then I pressed the belt to the snaps to leave an impression of the marker on the belt.  The belt is level and placed just below (but touching) the center button panel.
ed7d62f42fb0c5fb85be0343a160ca48.jpg

This leaves nice marks where the snaps should go.  I did this process twice - just to be sure.
280a8552ddc4b7c1c5fb60533aad5222.jpg

 

Belt in place.  I still need to trim and glue on the rivet covers.  I used Tandy small single cap rivets to attach canvas belt to ABS ammo pack.  The docking bay 94 captain actually has a low fitting belt - it looks like is has fallen down post-weathering.  I will need to reposition this belt for SWAT application - but I am told that I need to have the belt here for basic approval.  I find it weird that something good enough for L3 approval is not good enough for basic.  Oh well.  anyway, I was going to install another set of snaps to allow me to easily adjust this in the future - but I forgot and put on the ammo pack before adding the snaps. 
e3fed9fbc40a674d8ba164e503e18ce6.jpg
 

Link to comment
Share on other sites

2 hours ago, Airborne Trooper said:

I would recommend using the non-Tandy labeled snaps where visible. At least on the top right side. 

As much as I prefer Tandy... .  Will do.  At least for the right ab.  :salute:

Link to comment
Share on other sites

  • 3 weeks later...

Minor progress these last few weeks. Life with young children is not conducive to building armour - plus we’ve been away on vacation for a bit. Oh well, here are some more check boxes that I’ve checked off.

I managed to get all the holes drilled for the original bracket strapping system and tested some of the connections. I also did some more minor reshaping of some return edges with the always scary heat gun.

Drilling holes.
32f646dd7a403c0f652b76c491f85509.heic

Glued 3 button plate.
9d47bbd6c3e854609851f5192b8b8e10.heic

Glued rivet covers on belt.
2acce4b3779f84bd35b00704aea83fda.heic

And started painting a bunch of screws and rivets white.
35fb55abb4c8fc5e1d2a35ffb9fa1537.heic
 


Started to add the canon bracket strapping.
3678e7801d95f48cfc682b24fa98f8ed.jpg

I managed to get the screws counter sunk a bit.
13cabbee374f488f99424c3c368fbb1e.jpg

I have seen other people use elastic along the left kidney to abdomen connection. They also used a extra piece of ABS to support it. I tried the same method, but once I got the split rivets set, a gap formed. The elastic got stretched a little a now won’t retract due to the ABS support.
e6b099bf7e60dd14adf1beed9726693d.jpg

This is a lot more gap than I want. Not too happy.
208bd1086c41d71eb908ccee0bc5cc9b.jpg

I changed out the right ab snap for a “Tandy”-less snap.
0b448280d6d508618d991fc577ba6138.jpg

Added some bits of ABS to the inside of the thighs. I will ABS paste the outside. The screen used thighs appear to be filled as well - probably paint.
3726b4569ed959c6763aa52d8c100269.jpg
Reference
f86b2c390c24243d2ae87072428cc384.jpg
ee102da7dafe480eedb322fae1c35078.jpg

Snap bases for shoulder straps. I also added a snap base opposite the right ab snap (not shown)
adf7d974e53dc4dee0f2c78adc929fa5.jpg

25mm coverstrips for back of shins. Adding Velcro before gluing. I’ll see how that works.
4ee52b5227ac043dcbc45ee7c66b74ad.jpg

Just waiting for one snap base to set.
1299dda93ac57e6fe4b90e5f8e7f03e7.jpg

Happy belated Father’s Day. My wife ordered me a couple of helmet bags from Trooperbay. She even knew that one should be TD. Just when you think they don’t care... :)
c3686d94694de3441fed54409398fd60.jpg
a6a2209e5574f6759e75b4d091ec11d1.jpg
 

  • Like 1
Link to comment
Share on other sites

It is funny how these things come together. After picking away at little things for what seemed like forever - I started adding some strapping and viola, I can see the light at the end of the tunnel. I just need to finish some arm strapping and the basic build is done.

For various reasons I am not using the original bracket strapping system for the chest. So I glued in some snap plates about 4inches up from the lower return edge.
2932801c6e0f98fc2981f8a6183d80f3.jpg

Added snap bases near the top edge of the ab.
cd64d31b5425573b26d41554171e7d2e.jpg

Taped chest to ab to double check alignment.
6bd3732f32921ad7cbb6d449d7a7caa0.jpg

Realized I need to shift a snap base.
a6d67a037f94dd89935ec6cf9494902e.jpg

Test fit. I’m trying to get the placement if the chest with relation to the ab to match the reference (more or less) but still fit okay. I did need to redo one chest to ab strap because the chest was slightly skewed.
8a2b7dddc11242f7db00e91b63e974d3.jpg
Reference
050a7b7b85b460d81c63943bb0947327.jpg

Left side (mirror) pic. More gap than I would like, but not terrible.
420b9a2c9f9f7bc576b13a4148f9fbee.jpg

Right side mirror pic. I’m using a plastic reinforced nylon strap for the right connection. It doesn’t overlap but it does cause the two haves to offset like this. May need to revisit this.
a39605c2274bf83c8f235f656e40527d.jpg

And back. The gap between the back plate and the kidney plate is a lot less here than on my first TK. I’ll need to hot bath the shoulder tabs at the back to bend them down a bit - they are sticking up about half an inch or more above my shoulders.
195cc462c30c80e4d8543dff0ff2097d.jpg

 

Link to comment
Share on other sites

Weathering test number one.
Although I like the look of the subtle weathering one gets with Fullers Earth, I worry about the durability and, more importantly, I need to be able to carefully control the pattern of the weathering. I feel I can do that better with paint since I have experience painting and zero experience with Fullers Earth.

Try one is using regular art acrylics and a shop towel to dab the paint for texture.

I used burnt umber, black, yellow ochre, and white.
c8d699542083f2e8c0f6d5df74480d42.jpg

I started off drawing a pattern and filling it in with dark grey. Then I did a coat of brown. Then a coat of sand colour. After each layer I rubbed off most of the paint with a towel.
680161788f3a75e47d51adf86f956445.jpg

Well, I wasn’t happy at all with that. Too dark. So I wiped the piece clean with some mineral spirits and tried again.
45c129e82de63f9d22c54b63a6f2fd72.jpg

Outline pattern.
79e5c0b680a69167f145076e4189085c.jpg

Paint in area.
3e55f37c20e74007aa36dbae09233e58.jpg

Dab with towel and spread some paint around.
0bd6c9271fa466b7b771e4d58461092e.jpg

A layer of brown/tan colour and dab with a towel.
9cbe141db574e2f91c1fc17ef2115b8e.jpg

Rub away some paint once dry.
ab22ebc9acb04ba1b5bb4da0c7d38fd7.jpg

Flick some brown and yellow at it.
5cf3be5efa7997de6d2f5cf51fa53b9c.jpg

Rub off some of the specks. I needed to use mineral spirits for the flecks as they were pretty stubborn.
5b361e0f88693660771e17699523fdb6.jpg

In sunlight at a distance.
c02333c2220a51cff59bec8857e0412e.jpg
Sunlight, bit closer. Not terrible.
3f2f2c75bd9cc631a84b8324f3309b95.jpg

I will try the same thing tomorrow but I’ll use an airbrush.

Link to comment
Share on other sites

From the times I've seen it, airbrushing makes it look unnatural. Apply some watered down burnt umber with a sponge. Let it begin to dry and then blot most of it off with a paper towel. You can achieve layers with this method. 

Link to comment
Share on other sites

2 hours ago, Airborne Trooper said:

From the times I've seen it, airbrushing makes it look unnatural. Apply some watered down burnt umber with a sponge. Let it begin to dry and then blot most of it off with a paper towel. You can achieve layers with this method. 

Yeah, I'll probably do that to create a darker base layer(s) when I actually do the armor.  I also want to get that dusty look that the Fullers Earth gives.  I tried the same process with the airbrush and using washes of acrylic.  I did do a quick layer of  burnt umber as you mentioned - I will do more next time.  As for the airbrush - I use the incorrect nozzle/needle combination.  This causes the paint to splatter and spit a little.  Gives a gritty texture.  Anyway, here is a test - the airbrush is on the right.  It needs a bit more contrast (darker burnt umber) in a few places. It doesn't read as strong on camera (especially in sunlight) - but it looks pretty realistic in person.

58d9cc81099f83c25120f3501623169f.jpg

Link to comment
Share on other sites

Final push before I can start weathering.  Here are some of the things I finished up.

Tube stripes. All the painting will be done by hand. Here, I am measuring out the spacing for the stripes.
9866e84b2ec908d3c136b2612d53fa9c.jpg

First coat. Yuck, I hate doing these things.
86686be007493c47184ae40fdf8d2ac2.jpg

Oh, I also did the vocoder. I forgot to mention that I composited original photographs over photographs of my helmet in Photoshop to place the stripes and vocoder details.
f1cf79069181f39af1c76f39a092c5c6.jpg

Had to place and drill the holes for the Hovi mics . The HOVI mics in the reference picture do not seem to match where the holes are marked for the AP helmet. So, I had to adjust. I also painted the tips of the Hovi mics white as per the reference picture.
621953838b4ebbec7a0d4af1260cd71d.jpg

Taped off an area for the crack/paint run on the top of the helmet.
b9989de0da30e5991c72be4b83e06b7f.jpg

The colour was supposed to match HDPE green plastic colour of the original helmets. But this is a bit dark, I will have to tone it down with some white paint.
3b69d7ab7dd9821353d8221a4401282c.jpg

I also cut some tubing at some funny angle to help redirect the Hovi mics . It is difficult to get them to point in the right direction.
66ad5b6c19880e3e8c2fcae81d20b73e.jpg

Also final trimmed and sanded the legs and arms. I also added all the snap bases. For sanding, I use 220 grit, 320 grit, 400 grit, and 600 grit. All the return edges were sanded this way for comfort... especially in the upper thigh area.
55322c01d5e9c137df2be637acd8b7d3.jpg

And then the next day...

Ammo pack and some final strapping. Still waiting for the tube stripes to fully dry before I can clean them up.

Ammo pack riding low.
1a740162ba814616f36bba2e61fd368e.jpg

15c048506169412f61b1a9c0619617d5.jpg

Single cap rivet
daaea536104249b36f9a7995a11215fe.jpg

399adc8c171713f591d9287445a6fa65.jpg

Arms ready to go. Once some glue drys.

c22635bd4f744f23ab9c339f0eb01205.jpg

 

I just noticed that the captain does not have bicep hooks.  I guess I'll have to change that sometime later.

ae9853edccb615f90a741c56b07b2621.jpg


Come on paint... dry.
b1cbbb1418524818977fe93618bee135.jpg

Once I can do a full test fit and if things seem good then I can finally get dirty. Oh, and glue the silicone hand guards to the gloves - tomorrow.
 

Then tomorrow came...

So, the tube stripes were finally dry! So I clean them up a little bit and quickly assembled the helmet. I did not install the lens yet and the Hovi mics still need some adjustments. I will also also need to add the HDPE green colour to the crack on the cheek. After some research I think I found a very close colour match to use on the helmet. I will redo the crack on the top of the helmet as well.

36b1aa194a27c05fdaf66535412c9c87.jpg
4c6a27ea550ea7dec57572145978adb8.jpg
85467673615dcaab8606a9806fbc26b7.jpg

I cobbled together a makeshift thigh garter. 3 inch elastic and 2 inch nylon webbing and a buckle. And a bunch of tape.
231e0b2227017b2a214c5f8cfd224e9d.jpg

So I was finally able to do a test fit. My makeshift thigh garter system did not hold up very well and the thighs have dropped a bit in the pictures. The shins have also rotated, I will need to add some Velcro to the boots and the insides of the shins. I also noticed that I will need to hot bath the back tabs on the shoulders so they don’t stick up so much.
c0cedb58dbeca8354c391afdec2b6272.jpg
19c37459d1e8337829b9ce8f480bd75c.jpg
cf70852eda54e0e2f4445c6f3b37c8fd.jpg
a97072f3a9c492f0b074a8a9761ba938.jpg

I meant to add these parts as well. However, my bucket did not have any fans in it, I had forgotten how hot it gets without the fans. So this fitting was short-lived.
6de66b3b22e4e2bb94cecd3ec1b23854.jpg

Hot bathing the tab. The one on the left has been adjusted for comparison. deb64844815833d809cbc442c79d4427.jpg

Overall, the fitting seemed pretty good. The true test will be walking around for an extended amount of time to test how the return edges will feel. So, it’s finally time for the weathering. Woo hoo.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...